Run the Pantilt Demo

Version 34 (Jesse French, 02/13/2015 01:48 pm)

1 5 Rich LeGrand
h1. Running the Pan/tilt Demo
2 1 Rich LeGrand
3 34 Jesse French
OK, you've [[Assembling pan/tilt Mechanism|assembled the pan/tilt mechanism]] and it looks cool, but it would look even cooler if it moved.  One nice thing is that you don't need a battery to move the pan/tilt -- the pan/tilt can use the USB cable for power, *as long as the cable is 4 ft or shorter*. (3 ft is common, and even better.)  If you use a longer cable, there can be up to 1 volt of voltage drop along the cable, which is fine for Pixy, but the servos will malfunction.  Also, before you run the pan/tilt demo, go ahead and [[Teach Pixy an object|teach Pixy an object]] if you haven't already.  
4 1 Rich LeGrand
5 34 Jesse French
We should also mention that the pan/tilt base needs to be anchored to the table somehow before running the demo.  Use a couple pieces of tape, if you like -- it doesn't take much -- or use a binder clip to attach the pan/tilt base to a magazine.  If you don't anchor the base, the base will tend to rotate under Pixy, leaving Pixy more or less stationary (and we want Pixy to move/rotate!)   
6 26 Rich LeGrand
7 15 Rich LeGrand
There are three ways to run the pan/tilt demo.
8 1 Rich LeGrand
9 17 Rich LeGrand
h3. *Running the demo by using the button press sequence*
10 1 Rich LeGrand
11 1 Rich LeGrand
When Pixy first powers up, you'll notice that the LED turns on (white) for about 1 second, then flashes, then turns off.  What's really happening is Pixy is asking you which program you want to run.  Currently, Pixy ships with two programs:
12 1 Rich LeGrand
13 1 Rich LeGrand
# the default tracking program that detects objects and streams them out the port you choose
14 1 Rich LeGrand
# the pan/tilt demo
15 1 Rich LeGrand
16 12 Rich LeGrand
So, power up Pixy, and when the LED turns on (white), hold down the button. The LED will turn red then orange, red then orange, etc. If you release the button when the LED is red, you will select the default tracking program.  If you release the button when the LED is orange you will select the pan/tilt demo. So do that -- release the button when the LED is orange.  The LED will flash orange a couple times which means "running program 2!" 
17 1 Rich LeGrand
18 12 Rich LeGrand
And then Pixy should track your object.  Yay!
19 1 Rich LeGrand
20 32 Jesse French
A quick note on program selection -- normally, upon power up, if you don't press the button, Pixy "times-out" and just runs the default program, which is the tracking program, but you can configure which program is the default program from the "PixyMon Configure Dialog":/projects/cmucam5/wiki/Expert_Pane. 
21 1 Rich LeGrand
22 18 Rich LeGrand
h3. *Running the demo from PixyMon*
23 1 Rich LeGrand
24 10 Rich LeGrand
If you're running PixyMon, you can run the demo (or any other program) at any time by selecting it in the *Action* menu.  In particular, select *Action➜Run the pan/tilt demo*. 
25 1 Rich LeGrand
26 23 Rich LeGrand
Pixy should then track your object and plot the detected objects in the video window. Yay! 
27 1 Rich LeGrand
28 28 Rich LeGrand
Here's a short video:
29 29 Rich LeGrand
30 28 Rich LeGrand
{{youtube(xTOyQOSswUE, 480, 360)}}
31 28 Rich LeGrand
32 34 Jesse French
From PixyMon, you can also play with the pan/tilt demo parameters:
33 21 Rich LeGrand
34 31 Rich LeGrand
!http://i74.photobucket.com/albums/i241/cmucam/Image163_zpsd178a0d5.jpg!
35 21 Rich LeGrand
36 31 Rich LeGrand
For example, try changing the Pan P gain (pan axis proportional gain) from 500 to 50, then hit *Apply*.  Or increase the gains and see what happens.  Many times, increasing the gains results in some erratic behavior, but don't worry -- you won't damage anything.  If you want to go back to the default values select *Action➜Restore default parameters*.  There is more information "here":/projects/cmucam5/wiki/Pantilt_Demo_Pane.
37 21 Rich LeGrand
38 18 Rich LeGrand
h3. *Running the demo from an Arduino*
39 13 Rich LeGrand
40 18 Rich LeGrand
You can have your Arduino perform pan/tilt tracking too.  The Arduino reads in the object blocks and calculates the positions of the pan and tilt servos and sends the calculated positions back to Pixy, and Pixy then updates the servo positions.  This is great for getting your Pixy and Arduino better acquainted and getting them both collaborating in some kind of application that you write. 
41 13 Rich LeGrand
42 18 Rich LeGrand
*This requires that you run the "default" Pixy program -- not the pan/tilt demo program.* The default program is the program Pixy runs upon power-up by default without pressing any buttons.  You can also run the default program by selecting it in the *Actions* menu in PixyMon. 
43 16 Rich LeGrand
44 32 Jesse French
OK, start by getting the latest Arduino-Pixy code, described [[Hooking up Pixy to a Microcontroller like an Arduino|here]].  Load the pantilt demo by selecting it in *File➜Examples➜Pixy➜pantilt* in the Arduino IDE.  Upload it, and as long as Pixy is running the default program, you should start seeing the pan/tilt move to track any object that matches signature 1. (Note, you'll need to "teach Pixy an object":/projects/cmucam5/wiki/Teach_Pixy_an_object_2 if you haven't done so already.)
45 13 Rich LeGrand
46 18 Rich LeGrand
You can also play with the Arduino code, such as changing the proportional and derivative gains. 
47 13 Rich LeGrand
48 13 Rich LeGrand
<pre>
49 33 Rich LeGrand
ServoLoop panLoop(300, 500);
50 33 Rich LeGrand
ServoLoop tiltLoop(500, 700);
51 13 Rich LeGrand
</pre>
52 1 Rich LeGrand
53 33 Rich LeGrand
Here, 300 is the proportional gain and 500 is the derivative gain for the pan servo.  Likewise, 500 and 700 are the proportional and derivative gains for the tilt axis.  Try reducing the proportional gain in half and see what happens. Many times, increasing the gains results in some erratic behavior, but don't worry -- you won't damage anything.  
54 19 Rich LeGrand
55 33 Rich LeGrand
With a little tweaking and modifying, this code can become a "chasing" instead of a "tracking" algorithm. That is, instead of calculating servo positions your Arduino can calculate motor speeds.  So now your Pixy-Arduino robot creation can chase a ball, toy, etc.  Adafruit created just such a robot, and they describe how to build and program one "here":https://learn.adafruit.com/pixy-pet-robot-color-vision-follower-using-pixycam.  
56 13 Rich LeGrand
57 13 Rich LeGrand
58 13 Rich LeGrand
 
59 1 Rich LeGrand
60 1 Rich LeGrand